四周包有絕緣線材的细小型黃銅制鱷魚夾。
鋸齒狀下頜可以夾取較大尺寸物體，也可以夾取細電線。
位於絕缘體内的Ø 4 mm硬質插座與帶硬質絕缘套管的彈簧式Ø 4 mm插頭配合使用。

Small, slim, made of brass with all-round insulation.
Toothed jaws for wide grip with surface for fine wire.
Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

帶柔性桿和彈簧鋼絲夾的測試夾，適合與插针或不易接接觸的電線連接。
桿體帶硅膠絕缘，耐熱性好，且在低溫下也能保持高柔軟性。
把手處Ø 4 mm的硬質插座與带硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。

With flexible shaft and spring wire grabber (stainless steel) for a good contact to pins and wires in inaccessible places.
Especially suitable for measuring voltages. The shaft is silicone insulated and guarantees good heat resistance and flexibility even at low temperatures.
Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs withrigid insulating sleeve.

帶椎形不鏽鋼硬針頭的測試探頭，手柄兩端進行倒角處理。
把手處Ø 4 mm的硬質插座與帶硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。配有保護蓋。

Test probe with tapered, stainless steel rigid needle. Handle guard chamfered on both sides.
Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Supplied with protective cap.

带硬質錐形不銹鋼針頭的測試探頭，手柄兩端進行倒角處理。
把手處Ø 4 mm的硬質插座與带硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。配有保護蓋。

Test probe with tapered, stainless steel rigid needle and with handle guard chamfered on both sides.
Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Supplied with protective cap.

彈簧式不銹鋼探針可輕壓回彈，特别適合應用於敏感印刷電路。
手柄兩端進行倒角處理。
把手處Ø 4 mm的硬質插座與带硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。
配有保護蓋。

Spring-loaded stainless steel needle which reacts resiliently under light pressure.
Specially suited for sensitive printed circuits.
Test probe with handle guard chamfered on both sides.
Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Supplied with protective cap.

绝缘型硬质插座，Ø 4 mm，黄铜。
可对接带有硬质绝缘套管的Ø 4 mm弹簧式插头。
插座可以螺纹安装在塑料或金属等材质的面板上。

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
The socket is screwed into pre-drilled panels of plastic,metal, etc.

絕缘型硬質插座，Ø 4 mm，黃銅。
可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。
插座可以螺纹安裝在塑料或金属等材質的面板上。
連接方式：M4螺栓和焊接孔

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
The socket is screwed into pre-drilled panels of plastic,metal, etc.
Connection: Threaded bolt M4 and soldering hole.

絕缘型硬質插座，Ø 4 mm。可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。
插座可以螺纹安裝在塑料或金屬等材質的面板上。
連接方式：扁平連接片

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
The socket is screwed into pre-drilled panels of plastic,metal, etc.
Connection: Flat connecting tab.

絕缘型硬質插座，Ø 4 mm。可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。
插座可以螺纹安裝在塑料或金數等材質的面板上。
連接方式：扁平連接片

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
The socket is screwed into pre-drilled panels of plastic,metal, etc.
Connection: Flat connecting tab.

絕缘型硬質插座，Ø 4 mm。可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。
插座可以壓入式安裝在塑料或金属材質的面板上。
連接方式：扁平連接片

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
The socket is pressed into pre-drilled panels of plastic,metal, etc.
Connection: Flat connecting tab.

帶硬質絕緣套管，Ø 4 mm，堆疊式插頭，採用
MULTILAM技術，用於自組裝測試導線。有鍍
金和鍍鎳可供選擇。

Stackable, Ø 4 mm, with spring-loaded
MULTILAM,
for self-assembly of test leads.
With rigid insulating sleeve. Nickel-plated
and gold-plated versions available.

絕缘型硬質插座，Ø 4 mm。可對接帶有硬質絕 連接方式：扁平連接片
缘套管的Ø 4 mm弹簧式插頭。插座可以螺纹
安裝在塑料或金属等材質的面板上。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Machined brass. The socket
is screwed into pre-drilled panels of plastic,
metal, etc. Connection: Flat connecting tab.

絕缘型硬質插座，Ø 4 mm，黃銅。可對接帶有
硬質絕缘套管的Ø 4 mm弹簧式插頭。插座可以螺纹安裝在塑料或金属等材質的面板上。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Machined brass. The socket
is screwed into pre-drilled panels of plastic,
metal, etc.

用於自组裝的測試導線，Ø 4 mm，堆疊式
插頭，採用MULTILAM技術。產品帶有伸缩
套管可防止意外觸摸。由於插頭装有防護頸
圈，電器間隙和爬電距離增加，因此，裝配此款插頭質，即使一些老式測試儀器没有
安裝安全插座，不符合高达600 V CATII的
安全裝置，測試導線也可以與之安全連接。

Stackable, Ø 4 mm, with spring-loaded
MULTILAM,
for self-assembly of test leads.
With retractable sleeve to prevent accidental
touching. As a result of the protective collar,
the clearances and creepage distances allow
test leads equipped with this plug also to be
safely connected to older test instruments
not yet fitted with safety sockets up to 600 V,
CAT II in accordance with the standards.

帶絕緣，Ø 4 mm，硬質，黃銅。絕緣體帶金屬
螺紋護套，面板螺纹式安裝。有六角和圆形兩種螺母可選。

Insulated, Ø 4 mm, rigid. Machined brass.
Metal thread jacket on the insulation. The
socket can be screw-mounted in predrilled
panels. Available with hexagonal or round
nut.

帶絕緣，Ø 4 mm，硬質，黃銅。絕緣體帶金屬
螺紋護套，面板螺纹式安裝。有六角和圆形兩種螺母可選。
扁平連接片4.8 mm x 0.8 mm

Insulated, Ø 4 mm, rigid. Machined brass.
Metal thread jacket on the insulation. The
socket can be screw-mounted in predrilled
panels. Available with hexagonal nut.
Flat connecting tab 4.8 mm x 0.8 mm.

帶絕緣，Ø 4 mm，硬質，黃銅。面板壓入式安裝。

Insulated, Ø 4 mm, rigid. Machined brass.
The socket is pressed into predrilled panels
of plastic, metal etc.
Flat connecting tab 4.8 mm x 0.8 mm.

帶絕緣，Ø 4 mm，硬質，黃銅，面板壓入式安裝。扁平連接片4.8 mm x 0.8 mm,可90°彎曲，但僅能彎曲一次。

Insulated, Ø 4 mm, rigid. Brass sheet,
punched and rolled. The socket is pressed
into predrilled panels of plastic, metal etc.
Flat connecting tab 4.8 mm x 0.8 mm, can
be bent to 90°, once only.

带絕緣殼和螺栓，黃銅，可與螺纹孔進行連接。可與帶硬質絕緣套管的彈簧式Ø 4 mm插頭配合使用。插座帶内槽，可使用螺絲刀。

Insulated, with external thread for screw connection
to threaded holes. Machined brass.Ø 4 mm rigid socket in insulator accepting
spring-loaded Ø 4 mm plugs with rigidinsulating sleeve. Socket with internal slot
for screwdriver.

带絕緣殼和螺栓，黃銅，可與螺纹孔進行連接。可與帶硬質絕緣套管的彈簧式Ø 4 mm插頭配合使用。插座帶内槽，可使用螺絲刀。

Insulated, with external thread for screw connection
to threaded holes. Machined brass.Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigidinsulating sleeve. Socket with internal slot for screwdriver.

硬質適配器，非常適合與電能表的夾子進行螺
纹連接。適配器内的Ø 4 mm硬質插座與帶硬
質絕緣套管的彈簧式Ø 4 mm插頭配合使用。

Solid, especially suitable for the screw connection
to electricity meter clips. Can be
bent once to 90°. Ø 4 mm rigid socket in
insulator, accepting spring-loaded Ø 4 mm
plugs with rigid insulating sleeve.

帶絕緣，Ø 4 mm，硬質，黃銅，絕緣銅不可
拆卸。帶Ø 2.5 mm十字孔可與電線快速連接。與抗旋接線片配合，安裝在厚度為4 mm的前面板上。

Insulated, Ø 4 mm, rigid, and insulated
head undetachable. Ø 2.5 mm cross hole
for quick wire connection. Machined brass.
For mounting, with anti-rotation lug, in front
panels up to 4 mm thick.

黃銅材質，用於固定連接。比如：用於連接螺纹接線柱。適配器包含Ø 4 mm插座，可與带硬質絕緣套管的弹簧式Ø 4 mm插頭配合使用。叉
形接線片带45°彎曲。

Made of brass for permanent installation,
e.g. for connecting screw terminals.
Ø 4 mm rigid socket in insulator accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Fork lug bent to an angle
of 45°.

帶絕緣，Ø 4 mm，硬質，黃銅。面板螺纹式安裝。

Insulated, Ø 4 mm, rigid. Rolled brass sheet.
The socket can be screw-mounted in predrilled
panels.

黃銅材質，用於固定連接。比如：用於連接螺纹接線柱。適配器包含Ø 4 mm插座，可與帶硬質絕緣套管的彈簧式Ø 4 mm插頭配合使用。
叉形接線片可90°彎曲，但僅能彎曲一次。

Made of brass for permanent installation,
e.g. for connecting screw terminals.
Ø 4 mm rigid socket in insulator accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Fork lug can be bent once
to 90°.

絕緣型硬質插座，Ø 4 mm，黃銅。可對接帶有
硬質绝缘套管的Ø 4 mm彈簧式插頭。插座可以螺纹安装在塑料或金属等材質的面板上。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Machined brass. The socketis screwed into pre-drilled panels of plastic,metal, etc.

絕緣型硬質插座，Ø 4 mm，黃銅。可對接帶有硬質绝缘套管的Ø 4 mm彈簧式插頭。插座可以壓入式安裝在塑料或金屬等材質的面板上。
連接方式：扁平連接片4.8 mm × 0.8 mm， 可90°彎曲，但僅能彎曲一次。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Brass sheet. The socket is pressed into pre-drilled panels of plastic,metal, etc.

右轉角Ø 4 mm插座，黃銅，可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。
連接方式：Ø 2 mm圓針焊接於PCB板上

Insulated, right-angled Ø 4 mm rigid socket accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
Connection: Ø 2 mm round pin and contacts
for mounting on printed circuit boards.

絕缘型硬質插座，Ø 4 mm。可對接帶有硬質絕 連接方式：扁平連接片
缘套管的Ø 4 mm弹簧式插頭。插座可以螺纹
安裝在塑料或金属等材質的面板上。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Machined brass. The socket
is screwed into pre-drilled panels of plastic,
metal, etc. Connection: Flat connecting tab.

絕緣型硬質插座，Ø 4 mm。可對接带有硬質絕
緣套管的Ø 4 mm彈簧式插頭。插座可以壓入式安裝在塑料或金屬材質的面板上。

Insulated, rigid, Ø 4 mm, accepting
spring-loaded Ø 4 mm plugs with rigid insulating
sleeve. Machined brass. The socketis pressed into pre-drilled panels of plastic,metal, etc.

絕緣型硬質插座，Ø 4 mm，黃銅。可對接帶有
硬質絕缘套管的Ø 4 mm彈簧式插頭。插座可以壓入式安裝在塑料或金属材質的面板上。

Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid in-sulating sleeve. Machined brass. The socket is pressed into pre-drilled panels of plastic,metal, etc.

帶絕緣，Ø 4 mm，採用MULTILAM技術，抗震性能好，適合應用於自動化領域，如驅動器測試和维修。絕緣體内裝有Ø 4 mm硬質插座可與帶硬質絕缘套管的Ø 4 mm彈簧式插頭連接。

Insulated, Ø 4 mm, made of brass. Equipped with spring-loaded MULTILAM to ensure vibration-
proof contacts – ideal use is in the automotive field for test drives and servic ing. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

帶絕緣，Ø 4 mm，採用MULTILAM技術，抗震性能好，適合應用於自動化領域，如驅動器測試和维修。絕緣體内裝有Ø 4 mm硬質插座可與帶硬質絕缘套管的Ø 4 mm彈簧式插頭連接。

Insulated, Ø 4 mm, made of brass. Equipped with spring-loaded MULTILAM to ensure vibration-
proof contacts – ideal use is in the automotive field for test drives and servic ing. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

Ø 4 mm插頭，黃銅，採用MULTILAM技术。另一端絕缘體内帶Ø 4 mm硬質插座，可與帶硬質絕缘套管的Ø 4 mm彈簧式插頭連接。

Ø 4 mm plug, made of brass, with spring-loaded MULTILAM. Ø 4 mm rigid Ø 4 mm plug, made of brass, with spring-loaded MULTILAM. Ø 4 mm rigid

黃銅材質，用於固定連接。比如：用於連接螺纹接線柱。適配器包含Ø 4 mm插座，可與帶硬質
絕缘套管的彈簧式Ø 4 mm插頭配合使用。

Made of brass for permanent installation,e.g. for connecting screw terminals.Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

带硬質絕缘套管，Ø 4 mm短接插頭，黃銅。採用MULTILAM技術。

Insulated, Ø 4 mm, made of brass. Plugs with spring-loaded MULTILAM and rigid insulating sleeves.

帶絕缘，Ø 4 mm，黃銅，採用MULTILAM技術。絕缘手柄上有兩個直插式Ø 4 mm硬質插座，可與带硬質絕缘套管的Ø 4 mm彈簧式插頭連接。

Insulated, Ø 4 mm, made of brass. Plugs with spring-loaded MULTILAM. With insulated grip and with two in-line Ø 4 mm rigid sockets accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

無絕緣，Ø 4 mm，黃銅，採用MULTILAM技術。
带Ø 2 mm硬質插座，可与Ø 2 mm彈簧式插頭對接（兩端均可插入）

Insulated, Ø 4 mm plug, made of brass, with spring-loaded MULTILAM. Ø 2 mm rigid socket in insulator accepting spring-loaded Ø 2 mm plugs (pluggable on both sides).

帶絕緣、黃銅制直角適配器，可螺紋安裝於Ø 4 mm插座。此款適配器带可張開式Ø 4 mm螺紋插頭，可通過螺絲直接安裝於插座中。在連接狀態下提供完全的觸摸保護，適配器内的Ø 4 mm硬質插座可與帶硬質絕缘套管的彈簧式Ø 4 mm插頭配合使用。

Adapter, made of brass can be screw-mounted into Ø 4 mm sockets. The expandable Ø 4 mm plug of this adapter can be locked into the socket by tightening the grub screw. Assembled, the adapter offers complete
touch-proof protection. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

帶絕緣的柔性銅絲，可與多種螺絲鉗連接。比如：軌道式連接端子。絕缘體内含Ø 4 mm黃銅制硬質插座，可與帶硬質絕缘套管的彈簧式Ø 4 mm插頭配合使用。

Insulated flexible copper conductor, suitable for many types of screw clamp connections, e.g. rail mounted terminals. Ø 4 mm rigid socket in insulator, made of brass, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式空心插頭。

Highly flexible, with stackable Ø 4 mm hollow plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式空心插頭。

Highly flexible, with stackable Ø 4 mm hollow plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式空心插頭。

Highly flexible, with stackable Ø 4 mm hollow plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式插頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mm MULTILAM plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式插頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mm MULTILAM plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆叠式插頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mm MULTILAM plugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆疊式插
頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mmMULTILAMplugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆疊式插
頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mmMULTILAMplugs on both ends.

高柔軟測試導線，兩端均帶Ø 4 mm堆疊式插
頭，採用MULTILAM技術。

Highly flexible, with stackable Ø 4 mmMULTILAMplugs on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。

Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。
Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。
Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

PVC或矽膠絕缘的高柔軟導線，兩端為帶硬質絕缘套管的Ø 4 mm插頭，採采用MULTILAM技術。
Highly flexible, with insulation in PVC or silicone with stackable Ø 4 mm MULTILAM plugs with rigid insulating sleeve on both ends.

直插式，Ø 4 mm，採用MULTILAM技數，用於自組裝測試導線。L-41Q帶有測面接口，允許連接附加測試。
In-line, Ø 4 mm, with spring-loaded MULTILAM for self-assembly of test leads.Type L-41Q with Ø 4 mm lateral hole for additional test connection.Solder connection.

帶絕緣，Ø 4 mm，採用MULTILAM技術，抗震性能好，適合應用於自動化領域，如驅動器測試和维修。絕缘體内裝有Ø 4 mm硬質插座可與帶硬質絕缘套管的Ø 4 mm彈簧式插頭連接。

Insulated, Ø 4 mm, made of brass. Equipped with spring-loaded MULTILAM to ensure vibration-proof contacts – ideal use is in the automotive field for test drives and servic ng.Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

直插式，Ø 4 mm，採用MULTILAM技術，用於自組裝測試導線。
In-line, Ø 4 mm, with spring-loaded MULTILAM for self-assembly of test leads. Screw connection.

直插式，Ø 4 mm，採用MULTILAM技數，用於自組裝測試導線。L-41Q帶有測面接口，允許連接附加測試。
In-line, Ø 4 mm, with spring-loaded MULTILAM for self-assembly of test leads.Type L-41Q with Ø 4 mm lateral hole for additional test connection.Solder connection.

PVC或硅膠絕缘的高柔軟測試導線，一端为Ø 4mm測試探針，裝有MULTILAM；另一端為帶硬質絕缘套管的Ø 4mm插頭，直角，採用MULTILAM技術。包含保護蓋。
Highly flexible, with insulation in PVC or silicone.One end with Ø 4 mm test probe with spring-loaded MULTILAM,the other end with right angled Ø 4 mm MULTILAM plug with rigid insulating sleeve. Supplied with protective cap.

PVC或硅膠絕缘的高柔軟測試導線，一端为Ø 4mm測試探針，裝有MULTILAM；另一端為帶硬質絕缘套管的Ø 4mm插頭，直角，採用MULTILAM技術。包含保護蓋。
Highly flexible, with insulation in PVC or silicone.One end with Ø 4 mm test probe with spring-loaded MULTILAM,the other end with right angled Ø 4 mm MULTILAM plug with rigid insulating sleeve. Supplied with protective cap.

"右轉角Ø 4 mm插座，黃銅，可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭，符合IEC/EN61010-1規定，併帶觸摸保護。插座可以直接焊接在PCB板上，其右轉角的结抅可將因測試導線插入而產生的對線路板的應力減小到最低。
連接方式：Ø 2 mm圓真焊接於PCB板上"
"For mounting on printed circuit boards, touch-protected according to IEC/EN 61010-1. The socket is directly soldered onto printed circuit boards.The right-angled configuration minimizes the force transmitted to the printed circuit board through the plugged-in test lead.
Right-angled Ø 4 mm rigid socket accept ing spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass.
Connection:Ø 2 mm round pin and contacts for mounting on printed circuit boards."

"該適配器用於快速安全連接内六角螺纹/螺栓。鈕轉把手后端的按鈕打開六角尖端，以便適配器正好符合尺寸為5 mm或6 mm扳手的内部六邊形。這樣可以實現多點接觸和低接觸電阻。適配器在
負載下也可以用手操作。適配器内的Ø 4 mm插座可對接帶硬質絕缘套管的彈簧式Ø 4 mm插頭。
兩種不同設計
■■ 5 mm設計配有灰色按鈕
■■ 6 mm設計配有黑色按鈕"
"For fast, safe connection to screws/bolts with internal hexagon. Twisting the button on the back of the handle spreads the hexagonal tip so that the adapter fits firmly
into internal hexagons with 5 mm or 6 mm wrench size. This results in multiple contact points that enable low contact resistance.The adapter can also be operated by hand when under load. The fixed Ø 4 mm socket in insulator is suitable for fitting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Two different designs:
■ 5 mm design with gray button
■ 6 mm design with black button"

"該適配器用於快速安全連接内六角螺纹/螺栓。鈕轉把手后端的按鈕打開六角尖端，以便適配器正好符合尺寸為5 mm或6 mm扳手的内部六邊形。這樣可以實現多點接觸和低接觸電阻。適配器在
負載下也可以用手操作。適配器内的Ø 4 mm插座可對接帶硬質絕缘套管的彈簧式Ø 4 mm插頭。
兩種不同設計
■■ 5 mm設計配有灰色按鈕
■■ 6 mm設計配有黑色按鈕"
"For fast, safe connection to screws/bolts with internal hexagon. Twisting the button on the back of the handle spreads the hexagonal tip so that the adapter fits firmly
into internal hexagons with 5 mm or 6 mm wrench size. This results in multiple contact points that enable low contact resistance.The adapter can also be operated by hand when under load. The fixed Ø 4 mm socket in insulator is suitable for fitting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Two different designs:
■ 5 mm design with gray button
■ 6 mm design with black button"

"該適配器用於快速安全連接内六角螺纹/螺栓。鈕轉把手后端的按鈕打開六角尖端，以便適配器正好符合尺寸為5 mm或6 mm扳手的内部六邊形。這樣可以實現多點接觸和低接觸電阻。適配器在
負載下也可以用手操作。適配器内的Ø 4 mm插座可對接帶硬質絕缘套管的彈簧式Ø 4 mm插頭。
兩種不同設計
■■ 5 mm設計配有灰色按鈕
■■ 6 mm設計配有黑色按鈕"
"For fast, safe connection to screws/bolts with internal hexagon. Twisting the button on the back of the handle spreads the hexagonal tip so that the adapter fits firmly
into internal hexagons with 5 mm or 6 mm wrench size. This results in multiple contact points that enable low contact resistance.The adapter can also be operated by hand when under load. The fixed Ø 4 mm socket in insulator is suitable for fitting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Two different designs:
■ 5 mm design with gray button
■ 6 mm design with black button"

Ø 4 mm探頭，採用MULTILAM技術，把手一測採用扁平式處理，可以防止在使用时滚動，併允許探針緊靠着併排插入。把手處Ø 4 mm的硬質插座與帶硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。配有保護蓋。
Ø 4 mm, with spring-loaded MULTILAM. Handle guard flattened on one side to prevent rolling. Also allows for close side by-side plugging of probes. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Supplied with protective cap.

帶拋光型Ø 2 mm不鏽鋼尖頭，把手一測採用扁平式處理，可以防止在使用时滚動，併允許探針緊靠併排插入。把手處Ø 4 mm的硬质插座与带硬质绝缘套管的Ø 4 mm弹簧式插头配合使用。質配有保護蓋。
Polished Ø 2 mm stainless steel tip. Handle guard flattened on one side to prevent rolling. Also allows for close side-by-side plugging of probes. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Supplied with protective cap.

帶鋼制下頜的測試夾，特别適用於連接接地柱和大電纜。為了提高連接时的安全性，下頜有絕缘保護外層。把手處Ø 4 mm的硬質插座與帶硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。

With steel jaws especially for connections to ground rails and thick cables. For increased safety when making connections, the jaws are insulated on the outside. Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

带絕缘的黃銅制連接器，兩端均可對接帶硬質絕缘套管的Ø 4 mm彈簧式MULTILAM插頭。 Insulated, made of brass. Both ends suitable for accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

"絕缘型硬質插座，Ø 4 mm，黃銅。可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。插座包含兩個半圓型金屬導體，當插頭對接时導通，可用作開關功能。插座可以螺纹安裝在塑料或金屬等材質的面板上。
連接方式：2 × 扁平連接片4.8 mm ×0.8 mm。"
"Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Brass sheet. The socket consists of two insulated, semi-circular contacts, which are connected to each other when a plug is inserted (switch function).The socket is screwed into pre-drilled panels of plastic, metal, etc.
Connection: 2 × Flat connecting tab 4.8 mm × 0.8 mm."

"用於自组裝測試導線的Ø 4 mm硬質插座，可對接帶硬質绝缘套管的Ø 4 mm彈簧式插頭。
螺紋連接"
"Test accessories main catalog 81 In-line, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve, for self-assembly of test leads.
Screw connection."

"Monel®材質制作的Ø 2 mm探針，把手處Ø 4 mm的硬質插座與帶硬質绝缘套管的Ø 4 mm彈簧式插頭配合使用。
Monel® 是Special Metals公司的一个注冊商標。"
"Ø 2 mm, made of Monel®. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.
Monel® is a registered trademark of Special Metals Corporation."

"用於自组裝測試導線，Ø 4 mm插頭。採用
MULTILAM技術，並帶硬質绝缘套管。
螺纹連接"
"In-line, Ø 4 mm, with spring-loaded MULTILAM,for self-assembly of test leads. With rigid insulating sleeve.
Screw connection."

PVC，TPE或硅膠绝缘的高柔軟測試導線，兩端為帶硬質绝缘套管的Ø 4mm插頭，採用MULTILAM技術。由於TPE绝缘材料的绝缘電阻非常高，XMT-419測試導線非常適合於高阻抗測量。
Highly flexible, with insulation in PVC, TPE, or silicone with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends. Due to the very high insulation resistance of the TPE insulation, the test lead XMT-419 is excellently suited for measuring high resistances.

PVC，TPE或硅膠绝缘的高柔軟測試導線，兩端為帶硬質绝缘套管的Ø 4mm插頭，採用MULTILAM技術。由於TPE绝缘材料的绝缘電阻非常高，XMT-419測試導線非常適合於高阻抗測量。
Highly flexible, with insulation in PVC, TPE, or silicone with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends. Due to the very high insulation resistance of the TPE insulation, the test lead XMT-419 is excellently suited for measuring high resistances.

PVC，TPE或硅膠絕缘的高柔軟測試導線，兩端為带硬質絕缘套管的Ø 4mm插頭，採用MULTILAM技術。由於TPE絕缘材料的絕缘電阻非常高XMT-419測試導線非常適合於高阻抗測量。
Highly flexible, with insulation in PVC, TPE,or silicone with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends. Due to the very high insulation resistance of the TPE insulation, the test lead XMT-419 is excellently suited for measuring high resistances.

PVC，TPE或硅膠絕缘的高柔軟測試導線，兩端為带硬質絕缘套管的Ø 4mm插頭，採用MULTILAM技術。由於TPE絕缘材料的絕缘電阻非常高XMT-419測試導線非常適合於高阻抗測量。
Highly flexible, with insulation in PVC, TPE,or silicone with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends. Due to the very high insulation resistance of the TPE insulation, the test lead XMT-419 is excellently suited for measuring high resistances.

PVC，TPE或硅膠絕缘的高柔軟測試導線，兩端為带硬質絕缘套管的Ø 4mm插頭，採用MULTILAM技術。由於TPE絕缘材料的絕缘電阻非常高XMT-419測試導線非常適合於高阻抗測量。
Highly flexible, with insulation in PVC, TPE,or silicone with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends. Due to the very high insulation resistance of the TPE insulation, the test lead XMT-419 is excellently suited for measuring high resistances.

"測試導線帶有高熔斷保險絲，專為1000 V，CAT IV 應用設計，符合IEC/EN61010-031 標準。可以使用Ø 4 mm標準安全探針和測試夾進行帶熔斷保護的測量。裝有保險絲的二段式接頭可以扭開，易於進行保險絲更换。
P VC或硅膠絕缘的高柔軟測試導線，兩端為帶硬質绝缘套管的Ø 4 mm插頭，採用MULTILAM技術。二段式螺纹接頭可以安裝尺寸为6.3 x 32 mm的高熔斷保險絲。
保險絲需另購。
" "The test leads with integrated high breaking capacity fuses are designed for 1000 V, CAT IV in accordance with IEC/EN 61010-031 and allow for the use of Ø 4 mm standard safety probes and test clips for fuse-protected measurements.To change the fuse, the two-part fused connector can be easily unscrewed.
Highly flexible, with insulation in PVC or silicone.With in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends.The two-part screw connector accepts a high breaking capacity fuse measuring 6.3 x 32 mm.
The fuse is not supplied."

"測試導線帶有高熔斷保險絲，專為1000 V，CAT IV 應用設計，符合IEC/EN61010-031 標準。可以使用Ø 4 mm標準安全探針和測試夾進行帶熔斷保護的測量。裝有保險絲的二段式接頭可以扭開，易於進行保險絲更换。
P VC或硅膠絕缘的高柔軟測試導線，兩端為帶硬質绝缘套管的Ø 4 mm插頭，採用MULTILAM技術。二段式螺纹接頭可以安裝尺寸为6.3 x 32 mm的高熔斷保險絲。
保險絲需另購。"
"The test leads with integrated high breaking capacity fuses are designed for 1000 V, CAT IV in accordance with IEC/EN 61010-031 and allow for the use of Ø 4 mm standard safety probes and test clips for fuse-protected measurements.To change the fuse, the two-part fused connector can be easily unscrewed.
Highly flexible, with insulation in PVC or silicone.With in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends.The two-part screw connector accepts a high breaking capacity fuse measuring 6.3 x 32 mm.
The fuse is not supplied."

"測試導線帶有高熔斷保險絲，專為1000 V，CAT IV 應用設計，符合IEC/EN61010-031 標準。可以使用Ø 4 mm標準安全探針和測試夾進行帶熔斷保護的測量。裝有保險絲的二段式接頭可以扭開，易於進行保險絲更换。
P VC或硅膠絕缘的高柔軟測試導線，兩端為帶硬質绝缘套管的Ø 4 mm插頭，採用MULTILAM技術。二段式螺纹接頭可以安裝尺寸为6.3 x 32 mm的高熔斷保險絲。
保險絲需另購。"
"The test leads with integrated high breaking capacity fuses are designed for 1000 V, CAT IV in accordance with IEC/EN 61010-031 and allow for the use of Ø 4 mm standard safety probes and test clips for fuse-protected measurements.To change the fuse, the two-part fused connector can be easily unscrewed.
Highly flexible, with insulation in PVC or silicone.With in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends.The two-part screw connector accepts a high breaking capacity fuse measuring 6.3 x 32 mm.
The fuse is not supplied."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

P V C 或硅膠絕缘的高柔軟測試導線Ø 4 mm，採用MULTILAM技術。两端裝有堆叠式插頭，带防護頸圈和伸縮套管，可防止意外觸摸，尤其適用於不帶安全插座的電器設備。
"Highly flexible, with insulation in PVC or silicone especially suitable for connecting electrical devices not (yet) equipped with safety sockets. With stackable Ø 4 mm MULTILAM plugs on both ends with protective
collar and retractable sleeve to prevent accidental touching."

带硬質掛勾夾，鋼制，可以用来鈎住電纜。可繞探針縱向進行360°旋轉。把手處Ø 4 mm的硬質插座與帶硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。
With rigid hook clip made of steel for hooking onto wires. Rotatable through 360° around the longitudinal axis of the test probe. Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

高柔軟測試導線，兩端均為帶硬質絕缘套管的Ø 4 mm插頭，採用MULTILAM技術。

Highly flexible, with in-line Ø 4 mm MULTILAM plug with rigid insulating sleeve on both ends.

"硬質，絕缘，Ø 4 mm高壓插座。可對接ZHM-5000和XHL-5000測試導線。出於安全考慮，此插座與我们產品系列的Ø 4 mm插頭不兼容。
扁平連接片 4.8 mm x 0.8 mm"

"Insulated, rigid, Ø 4 mm for high voltages, to accept test leads XHM-5000 and XHL-5000. For safety reasons, the socket is not compat ible with any other Ø 4 mm plugs in our range.
Flat connecting tab 4.8 mm x 0.8 mm."

带鋼制下顎的測試夾，特别適用於連接接地柱和大電纜。為了提高連接时的安全性，下顎有絕缘保護外陳層。把手處的Ø 4 mm硬質插座與帶硬質絕缘套管的Ø 4 mm彈簧式插頭配合使用。

"With steel jaws especially for connections to ground rails and thick cables. For increased safety when making contacts, the jaws are insulated on the outside. Ø 4 mm rigid socket in handle accepting spring-loaded
Ø 4 mm plugs with rigid insulating sleeve."

用於連接螺絲或者螺栓。適配器包含Ø 4 mm插座，可與帶硬質絕缘外殼的Ø 4 mm彈簧式插頭配合使用。

For connection of screw heads with rigid Ø 4 mm socket in insulator, suitable for mating with spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

用於連接螺絲或者螺栓。適配器包含Ø 4 mm插座，可與帶硬質絕缘外殼的Ø 4 mm彈簧式插頭配合使用。

For connection of screw heads with rigid Ø 4 mm socket in insulator, suitable for mating with spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

用於連接螺絲或者螺栓。適配器包含Ø 4 mm插座，可與帶硬質絕缘外殼的Ø 4 mm彈簧式插頭配合使用。

For connection of screw heads with rigid Ø 4 mm socket in insulator, suitable for mating with spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

"用於自组裝測試導線，Ø 4 mm，採用MULTILAM技術。插頭帶有伸缩套管可防止意外觸摸。由於插頭莊有防護頸圈，電器間隙和爬電距離增加，因此，裝配此款插頭后，即使一些老式測試儀器没有安裝安全插座，不符合600 V CAT II的安全標準，測試導線也可以與之安全連接。
螺纹连接"

"In-line, Ø 4 mm, with spring-loaded MULTILAM,
for self-assembly of test leads. With retractable sleeve to prevent accidental touching. As a result of the protective collar,the clearances and creepage distances
allow test leads equipped with this plug also to be safely connected to older test instruments not yet fitted with safety sockets up to 600 V, CAT II in accordance with the standards.
Screw connection."

通體絕缘的海豚夾，黃銅，鋸齒狀下顎可以夾取較大尺寸物體，也可以夾取细電線。位於絕缘体
Made of brass with all-round insulation. Toothed jaws for wide grip with surface for fine wire. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

"絕缘型硬質插座，Ø 4 mm，黃銅。可對接帶有硬質絕缘套管的Ø 4 mm彈簧式插頭。插座可以螺纹安裝在塑料或金屬等材質的面板上。
連接方式：M4螺栓
可選配件：保護帽SD-XUB，用於在斷開狀態和閒置时蓋住插頭。（防護等級IP67）" Insulated, rigid, Ø 4 mm, accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve. Machined brass. The socket is surface-mounted, assembled flush, or pressed into pre-drilled panels of plastic,metal, etc. Connection: Threaded bolt M4. Optional: Protective cap SD-XUB to cover up unplugged, unused sockets (Protection degree IP67).

通體絕缘的鱷魚夾，黃銅，鋸齒狀下顎可以夹取較大尺寸物體，也可以夹取细電線。位於絕缘體内的Ø 4 mm硬質插座與帶硬質絕缘套管的彈簧式Ø 4 mm插頭配合使用。
Made of brass with all-round insulation. Toothed jaws for wide grip with surface for fine wire. Ø 4 mm rigid socket in insulator accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

用於在電壓測量中進行快速、安全連接的扁平測試夾，測試夾開口可調節。把手處Ø 4 mm的硬質插座可與帶硬質絕缘套管的Ø 4 mm彈簧式插头配合使用。
For making quick, secure contact during voltage measurements. With adjustable stop. Ø 4 mm rigid socket in handle accepting spring-loaded Ø 4 mm plugs with rigid insulating sleeve.

兩極，帶觸摸保護，用於BNC和Ø 4 mm系统的連接。有BNC公頭/Ø 4 mm插座，BNC公頭/Ø 4 mm插頭或者BNC母頭/Ø 4 mm插座，BNC母頭/Ø 4mm插頭等多種组合可選。Ø 4 mm插頭均採用MULTILAM技術。BNC接頭内部導體材質為黃銅，鍍金。
Two-pole touch-protected adapters withØ 4 mm connectors linked to the BNC system. Versions with BNC male or female connector and rigid Ø 4 mm sockets or Ø 4 mm MULTILAM plugs with rigid insulating sleeve. The contact pins and sockets of the inner conductor of the BNC plug connector are in gold-plated brass.

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。

Series introduction
D-1000 Series are the smallest connectors for signal lines among all the Dynamic connector series.
The Dynamic 1000 Series consists of 3 different pitch
sizes: 2.0mm standard type, 2.5mm high-voltage type and 3.5mm type.
D-1000 Series has gold plated contacts to maintain its high reliability and also tin plated contacts for economical market needs. Customers can choose their own contacts according to specifications, applications and cost.

系列介紹
它是Dynamic系列中，尺寸最小的系列。最適於用作工業設備配套的高可靠性信號線用連接器。連接器的間距，因所使用電流的大小，電壓的差異等，有標準型2.0mm間距，高電壓型
2.5mm間距及分線型3.5mm間距等數值，將來仍將根據市場需求，不斷擴充產品系列。
在保持高可靠性的同時，考慮到性價比，配備鍍錫型。根據工作環境，條件進行採用，有
助於降低成本。